Workspace

Projects

Sort by

Search projects

Loading your projects…

Step 1 of 8

How is it packaged?

Your container decides the canvas. Pick its type and size — or a custom label — and the artwork steps are built around it.

Packaging

Loading packaging options…

Select size

Container sizes from the Prooflet catalogue, with their measured dimensions and printable area. Each size lists only the artwork types it supports; unavailable ones say why.

Product category

Subcategory

Select a product category above — Prooflet derives the required Health Canada warnings from it.

Project name SKU name Brand SKU # (optional)

Your catalogue code — used in compliance reports and the spec sheet, never printed on the pouch.

Net size / variantUsed to name this SKU. Enter the declared weight or volume in Details & review. Number of SKUs

Making several SKUs that share this design? Each SKU becomes its own page in the exported print PDF (up to 16).

Artwork surface

Where your artwork is printed. Printed pouch: the artwork prints on the pouch itself. Pouch + pressure-sensitive adhesive label: a blank wholesale pouch you apply a separate adhesive label to — Prooflet suggests the largest label that clears the seals and closures. Choose one adhesive label, or author separate Front and Back labels as two independent dielines. Shrink sleeves are not supported.

Pouch style Units Pouch width Pouch height Seal depth

How far the heat-sealed edge extends into the pouch on each side. Artwork inside the seal band gets crushed by the sealing jaws, so the safe area starts after it. Your converter's spec sheet lists this value.

Gusset

Label width

Artwork type: pressure-sensitive label. This is separate adhesive stock applied to the container. Shrink sleeves use different seams, distortion and shrink zones; Prooflet does not author them yet. Do not enter a shrink-sleeve dieline as label dimensions.

Label height Corner radius (optional)

Back label width Back label height Back corner radius (optional)

Tube application

Choose which way the flat label runs when it is applied to the tube. Landscape needs a custom rectangular label plus a stated cap edge and front half. Catalogue and tapered tube labels stay portrait for now.

Application evidence — as viewed on the flat artwork

Landscape tube artwork can be authored and reviewed, but PDF/ZIP export remains blocked until the package records independent orientation evidence.

Tapered label

Moulded tubes are wider at one end, so a wrap label for one is die-cut as a trapezoid, not a rectangle. Take the narrow end width from your dieline when it prints both widths. Use the die-edge angle only when the narrow end is absent: dielines often round angles, and it is not the tube’s mould-draft angle. Wrapping a cone amplifies draft by about 3×, so the same 98 mm tube is drawn 0.5° on the moulder’s sheet and 1.7° on the converter’s die. Prooflet echoes the other figure back in your units; check it against your drawing.

Narrow end width Taper angle, per side (°)

Brand logo (optional)

Drag a file here, or

Brand name

Included in logo Add as text

Logo lettering still needs review.

You can also upload or replace the logo later in the editor.

Saved logos

No logos yet — a logo you save on a SKU shows up here for reuse.

Laminate finish

The physical film laminated to the pouch substrate (matte, soft-touch, gloss, satin). This is surface feel — "substrate intent" — not a print layer; it shows in the 3D preview and on the spec sheet.

Printed coating

A varnish printed as its own separation (an extra "ink" plate in the manufacturer file) — e.g. a full-surface matte varnish. Different from the laminate finish, which is a film, not ink. Leave as None unless your artwork spec calls for a coating.

Container colour (screen preview)

HEX—

CMYK—

Pantone—

Structural features

Resealable zipper Tear notch Hang hole Transparent window

SKU name-

Brand / SKU-

Product-

Warnings-

Pouch-

Colour-

Your pressure-sensitive label exports like any SKU: author the artwork, run the compliance check, and export the label package. Because this adhesive label IS the final label, every applicable required item must be pre-printed on it — choose Pre-print below, or export stays blocked by name. Shrink-sleeve artwork is not produced by this workflow.

Label information printed now or applied later

Production setup optional

Additional product details complete now or in the editor

Printed content is entered under Label information. These additional details support compliance review; missing information stays flagged.

Review the saved layout

Your colour, logo, THC symbol and current health warning are ready to arrange in the editor. Export creates the required warning variants.

Show brand name in preview

Live preview

Your brand

WARNINGMISE EN GARDE

5 × 7 in · 3-side seal

Rough guide only — arrange artwork and review the modeled compliance checks in the editor.