Workspace

Projects

Sort by

To set up new packaging, open app.prooflet.ca on a computer.

Search projects

Loading your projects…

Step 1 of 8

How is it packaged?

Pick the package. We size the artwork to it.

Packaging

Loading packaging options…

Select size

Pick your container; we fit the label to it. Sizes that can’t take this artwork say why.

Product category

Type

Select a product category above — Prooflet derives the required Health Canada warnings from it.

Project

Brand Company / licence holder (optional)Fills in the licence-holder box when it is printed on the pouch. Add the address and phone or email there. Size or variant (e.g. 30 g, Mango)Used in the SKU name. A weight or volume (e.g. 3.5 g, 50 mL) also fills in the declared net quantity. SKU # (optional)

Your catalogue code — used in compliance reports and the spec sheet, never printed on the pouch.

SKU nameNamed for you — change it if your team says it differently.

More than one product on this same pouch?

Products on this pouchOne setup, one print file, one page per product. Every page gets its own name, code and colour; size and net quantity are shared. Different size or quantity: make it a separate SKU.

Pouch style

Pouch size

Units Pouch width Pouch height

Printing details: 7 mm seal, flexographic — change

Print process Seal depth

How far the heat-sealed edge reaches into the pouch on each side. Artwork in the seal gets crushed, so the safe area starts after it. Your printer's spec sheet lists this value.

Finish

The film on the outside of the pouch: matte, soft-touch, gloss or satin. It shows in the 3D preview and on the spec sheet.

Extra varnish

A clear varnish printed over the whole pouch. Leave it as None unless your printer asks for one.

Gusset

Printed on

Where your artwork is printed. The pouch: the artwork prints on the pouch itself. The pouch plus a stick-on label: a blank wholesale pouch you apply a separate adhesive label to — Prooflet suggests the largest label that clears the seals and closures. Choose one label, or author separate Front and Back labels as two independent dielines. Shrink sleeves are not supported.

Label width

Artwork type: pressure-sensitive label. This is separate adhesive stock applied to the container. Shrink sleeves use different seams, distortion and shrink zones; Prooflet does not author them yet. Do not enter a shrink-sleeve dieline as label dimensions.

Label height Corner radius (optional)

Back label width Back label height Back corner radius (optional)

Tube application

Choose which way the flat label runs when it is applied to the tube. Landscape needs a custom rectangular label plus a stated cap edge and front half. Catalogue and tapered tube labels stay portrait for now.

Application evidence — as viewed on the flat artwork

Landscape tube artwork can be authored and reviewed, but PDF/ZIP export remains blocked until the package records independent orientation evidence.

Tapered label

Moulded tubes are wider at one end, so a wrap label for one is cut as a trapezoid, not a rectangle. Take the narrow end width from your dieline when it prints both widths. Use the label-edge angle only when the narrow end is absent: dielines often round angles, and it is not the tube’s mould-draft angle. Wrapping a cone amplifies draft by about 3×, so the same 98 mm tube is drawn 0.5° on the moulder’s sheet and 1.7° on the printer’s flat label drawing. Prooflet echoes the other figure back in your units; check it against your drawing.

Narrow end width Taper angle, per side (°)

Brand logo (optional)

Drag a file here, or

Is your brand name part of this logo?

Prooflet can’t read logo lettering, so you confirm it with the other review checks.

Yes, it’s in the logo No — add it as text on the pouch

You can also upload or replace the logo later in the editor.

Saved logos

No logos yet — a logo you save on a SKU shows up here for reuse.

Container colour (screen preview)

CMYK—

Pantone—

Structural features

Resealable zipper Zipper, mm from top Tear notch Tear notch, mm from top Perforation (tear line) Perforation, mm from top Hang hole Transparent window

SKU name-

Brand / SKU-

Product-

Health warning-

Pouch-

Colour-

Your pressure-sensitive label exports like any SKU: author the artwork, run the compliance check, and export the label package. Because this adhesive label IS the final label, every applicable required item must be pre-printed on it — under Change below, answer that your packaging line or your printer prints the lot and date, or export stays blocked by name. Shrink-sleeve artwork is not produced by this workflow.

Additional product details complete now or in the editor

Printed content is entered under Product details. These additional details support compliance review; missing information stays flagged.

Review the saved layout

Your product details go on the back panel. The front carries your logo, the THC symbol and the health warning.

Live preview

Pick the package to see a preview

Your brand

WARNINGMISE EN GARDE

130 × 180 mm · 3-side seal

Rough size guide — you’ll place your artwork in the editor.